germaillinois.blogg.se

6 Juni 2022 - 06:55
Cisco ios xe asr 1000 password hash type 8
Allmänt
Cisco ios xe asr 1000 password hash type 8













  1. #CISCO IOS XE ASR 1000 PASSWORD HASH TYPE 8 UPGRADE#
  2. #CISCO IOS XE ASR 1000 PASSWORD HASH TYPE 8 SOFTWARE#
  3. #CISCO IOS XE ASR 1000 PASSWORD HASH TYPE 8 CODE#
  4. #CISCO IOS XE ASR 1000 PASSWORD HASH TYPE 8 LICENSE#

The ASR 920 MPLS L2VPN configuration has been adopted from the following Cisco L2VPN Protocol-Based CLIs Guide:Īrista7150-L2 Vlan Trunk-ASR920-MPLS Core-ISR4321-M/Cast Host/PCġ) Vlan traffic is forwarded from the source Arista 7150 device via the L2VPN Xconnect to the ISR port /interface. On the remote ISR, a server/host is connected in order to join and receive the multicast stream. The ASR 920 GE I/face has been configured for MPLS L2VPN (Xconnect) functionality, where the intention is to extract specific vlan(s) using the "Ethernet Service instance" interface configuration for Layer 2 transport to a remote ISR 4321 (PE) router across the MPLS network.

#CISCO IOS XE ASR 1000 PASSWORD HASH TYPE 8 LICENSE#

The following EvalRTU license example displays the EvalRTU licenses used on the 10-GE ports.Multicast vlans from an Arista 7150 are trunked to a GE interface on the ASR 920.

  • The shut command on a 10-GE interface releases one count of the license, and the In-use count decreases by 1.
  • The no shut command on a 10-GE interface requests one count of the license, and the In-use count increases by 1.
    • If the EvalRTU license expires, it becomes a Right-To-Use (RTU) license.
  • The image carries 2-count 10-GE port EvalRTU (Evaluation) licenses.
  • An End-User License Agreement (EULA) will be displayed for each port if there is no permanent license present to support these ports.
  • Count-based licenses will be used for 10-GE ports, 1 count per port.
    • The 10-GE interfaces on the Cisco ASR 1001-X Router use a per port counted license, which has the following features: Per Port Counted License (10-GE Interfaces) show license all Command Output Description StoreIndex: 13 Feature: interface_10g Version: 1.0 StoreIndex: 12 Feature: vpls Version: 1.0 StoreIndex: 11 Feature: throughput_20g Version: 1.0 StoreIndex: 10 Feature: throughput_10g Version: 1.0 StoreIndex: 9 Feature: throughput_5g Version: 1.0 License State: Active, Not in Use, EULA accepted StoreIndex: 8 Feature: sw_redundancy Version: 1.0 StoreIndex: 5 Feature: lawful_intr Version: 1.0 StoreIndex: 4 Feature: ipsec Version: 1.0 StoreIndex: 3 Feature: fwnat_red Version: 1.0 License State: Active, Not in Use, EULA not accepted StoreIndex: 1 Feature: advipservices Version: 1.0 StoreIndex: 0 Feature: adventerprise Version: 1.0 License Count: 2/0/0 (Active/In-use/Violation) StoreIndex: 0 Feature: interface_10g Version: 1.0 The following example displays sample output from the show license all command: Primary License Storage stores the currently purchased and installed licenses. In the last 24 hours, sampling period is 300 seconds %BW_LICENSE-4-THROUGHPUT_MAX_LEVEL: SIP0: cpp_ha: Average throughput rateĪpproached the licensed bandwidth of 2000000000 bps during 1 sampling periods The configured throughput level in this example is 20 Gbps: System-forwarding plane approaches or exceeds the configured throughput license Will be displayed once every 24 hours if the traffic handled by the %IOSXE_THROUGHPUT-6-LEVEL: Throughput level has been set to 20000000 kbps Reboot level = adventerprise and License = adventerprise %IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_LEVEL: Module name = asr1001x Next Reloaded, the log messages at the router startup will display the license-levelĪnd throughput-level information, for example: The current throughput level is 2000000 kb/s Router# show platform hardware throughput level

    #CISCO IOS XE ASR 1000 PASSWORD HASH TYPE 8 UPGRADE#

    Output from this command after you apply the 20 Gbps performance upgrade Show platform hardware throughput level command. You can upgrade the throughput of the ESP from any license level toĬurrent throughput level of the ESP, run the Throughput of the ESP from 2.5 Gbps (default) to 5 Gbps, 10 Gbps, or 20 Gbps byĪpplying a software-activated performance upgrade license and then reloading

    #CISCO IOS XE ASR 1000 PASSWORD HASH TYPE 8 SOFTWARE#

    Gbps (default), 5 Gbps, 10 Gbps, and 20 Gbps depending upon the software Service processor of the Cisco ASR 1001-X Router supports throughputs of 2.5 Indicates the current requested Cisco lOS license level to boot. show running-config Command Output Description The following example displays sample output from the show running-config command: Use the show running-config command or the show startup-config command to view the license-level information. Indicates the startup configuration definition that will be used for the next reload instance. That would indicate that the purchase of a license is required. Indicates whether you are utilizing a permanent (purchased) license, an evaluation 60-day license, or a Right-to-Use license

    #CISCO IOS XE ASR 1000 PASSWORD HASH TYPE 8 CODE#

    Indicates the current Cisco IOS license code level. Use the show version command to determine the Cisco IOS license level in the router.















    Cisco ios xe asr 1000 password hash type 8
    0 kommentar(er)
    Om Mig: